SA-B26 Ashelle - Strike Bomber/CAS

1. Turn on power - BAT1 - 2
   
2. Turn on avionics bus
   
3. Turn on avionics key
   
4. [optional] Turn on APU - APU Fuel pump, APU Main
   
5. Turn on flight computer - ADIRS
   
6. Turn on fuel pumps - Left - Right - Centre
   
7. Turn on engine fuel pumps - 1 - 2
   
8. Turn on engine main - ENG 1 - 2 MAIN
   
9. Turn on lights as required - Position - Beacon - Strobe
   
10. Increase engine throttle to idle - 0.2
    
11. Enable engine starter mode - ENG 1 - 2 IDLE/START - [ON!]
    
12. Hold engine ignition until 200RPM - ENG 1 - 2 Ignition
    
13. Enable hydraulic systems - HYD A - B - C
    
14. Disable engine starter mode - ENG 1 - 2 IDLE/START - [OFF!]
    
15. Enable generators - GEN 1 - 2 BUS
    
16. [If enabled] Disable APU
    
17. Turn off parking brake

Notes: -[If ambient temperature below 0°C] - Enable Anti Ice - PROBE - WINGS - ENG1 - ENG 2 -Aircraft is trimmed for cruise speed with full loadout -> different speed/loadout might require retrimming

---

The aircraft is equipped with our advanced 4th gen avionics system "ANTARES" A total of 9 screens configurable on 2 touchscreens

1. Touchscreen map with waypoint controls - "+" and "-" is used for zoom, "R" will reset position on the map, Waypoint selection controls are described in autopilot controls
   
2. Horizontal situation indicator
   
3. Engine information - ENG 1 - 2
   
4. APU information
   
5. Enabled electrical systems information
   
6. Generators information
   
7. Fuel information
   
8. Weapon selection system
   
9. Onboard RADAR

---

This aircraft is equipped with an advanced autopilot system, it's 4 parts can be enabled seperately.

• Altitude hold
  
• Heading hold
  
• Roll stabiliser
  
• Waypoint autopilot

For altitude and heading hold Set your target altitude/heading on the middle dashboard monitor and enable the respective switch For waypoint autopilot You need to have a waypoint or more on the map in order to use this properly. There are 3 buttons in the right upper corner on the map screen (1) labeled "C","L" and "A". Button "A" will add a wapoint to the position you have selected on the map. "L" will delete your last waypoint and "C" will clear all waypoints.

---

You can cycle the selection with buttons on the middle bottom dashbord, as well as toggle the selected pylons. You can see your odnance status on the MFD Weapons selection screen(8) Multiple hardpoints can be selected at once All selected pylons can be dropped from either seat with hotkey[3] "Ordnance GPS" is used to set target coordinates for GPS guided ordnance "Ordnance Variable" is used for multiple variable sets, always optional, for example ordnance cruise altitude, depth charge detonation depth.. etc.. if the given type of ordnance supports 3rd variable Default loadout

• 4x - AGM 136 Radar/GPS guided AGM
  
• 2x - AIM 15 Radar guided AGM/AAM
  
• 2x - Type 54 wakehoming torpedo

You can equip the plane with any weapon from this pack

Crew - 2 pilots Length - 27.5m Height - 6.25m Wingspan - 34.75m Empty weight - 21544kg MTOW - 39980kg Max fuel - 33993L Fuel grade - Jet A1 Engine unit - Skytech J45A Unit power 5200hp/3850kW Top speed - 397kts/735kph Cruise speed - 210kts/389kph Stall speed - 115kts/213kph Combat range - 257NM/476km Max range - 631NM/1169km